enquiry button
  • slider
  • 01
  • 02
  • 03
- I. C. Engine Test Rigs
(Petrol)


- I. C. Engine Test Rigs
(Diesel)


- Exhaust Gas Analyser
(Petrol Engine)


- Sectional Working Model Of Automobile

- Automobile Lab Equipments

• SECTIONAL WORKING MODEL OF AUTOMOBILE

 
SECTIONAL WORKING MODEL OF TWO STROKE PETROL ENGINE
 
(Model Made from Aluminiam material witch demonstrates all engine parts)
 

 
PETROL ENGINE TWO STROKE IN CUT SECTION
 
This model is made out of used Bajaj engine, suitably sectioned to show the internal construction of the engine, gear box, clutch and rear wheel mechanism and the model is fitted on a sturdy iron frame. The complete internal details can be demonstrated by operating the kicker lever to show the working of the piston, sparks from the spark plugs can also be shown
 

 
PETROL ENGINE FOUR STROKE IN CUT SECTION
 
The engine and gearbox assembly, sectioning of maximum parts and accessories like cylinder, cylinder head, valve ports, gear box, housing, oil sump, etc will be carried out to show the internal constructional details such as piston, piston rings, valves, cam, connecting rod, etc. The model will be mounted on stand. The above model will be painted with spl duco painting, electroplating of hardware's will be carried out.
 

 
THREE CYLINDER FOUR STROKE PETROL ENGINE IN CUT SECTION
 
Actual original working engine is dissected wherever necessary so that all engine parts can be visualize.
 

 
FOUR CYLINDER FOUR STROKE PETROL ENGINE IN CUT SECTION
 
FOUR CYLINDER FOUR STROKE PETROL ENGINE IN CUT SECTION
 
Actual original working engine is dissected wherever necessary so that all engine parts can be visualize .
 

 
FOUR CYLINDER V-TYPE FOUR STROKE PETROL ENGINE IN CUT SECTION
 
Actual original working engine is dissected wherever necessary so that all engine parts can be visualize
 

 
SIX CYLINDER V-TYPE FOUR STROKE PETROL ENGINE IN CUT SECTION
 
The model is made out of full size original six cylinder, four strokes used diesel engine. Maximum parts and accessories like five cylinders, cylinder head, inlet and exhaust manifolds, fuel pump, oil pump, water pump, fuel filter, fuel injection pump, injectors, self-starter, dynamo, etc are sectioned to show the internal constructional details of the engine. Af. H. P. 220/230v a. C.
Motor is coupled through a reduction drive unit to the engine by which the model can be demonstrated at very low speed of about 15 to 20 RPM. By running the engine, the working of individual parts and accessories like crankshaft, camshaft, connecting rod, pistons, valves, different pumps, etc.. can be demonstrated.This model is provided upto flywheel and complete engine is mounted on a sturdy iron frame.
 

 
EIGHT CYLINDER V-TYPE FOUR STROKE PETROL ENGINE IN CUT SECTION
 
Actual original working engine is dissected wherever necessary so that all engine parts can be visualize
 

 
MPFI THREE CYLINDER FOUR STROKE PETROL ENGINE IN CUT SECTION
 
Actual original working engine is dissected wherever necessary so that all engine parts can be visualize
 

 
CNG THREE CYLINDER FOUR STROKE PETROL ENGINE IN CUT SECTION
 
Actual original working engine is dissected wherever necessary so that all engine parts can be visualize
 

 
CNG FOUR CYLINDER FOUR STROKE PETROL ENGINE IN CUT SECTION
 
Actual original working engine is dissected wherever necessary so that all engine parts can be visualize
 

 
REAR AXEL ASSEMBLY WITH DIFFERENTIAL IN CUT SECTION
 
REAR AXEL ASSEMBLY WITH DIFFERENTIAL IN CUT SECTION
 
Original second hand rear axel assembly of car or jeep is suitably sectioned to demonstrate the working of bevel & pinion crown wheel, two plant gears & two sun gears, final drive gear shafts & brake drums complete unit is fixed on sturdy wooden base.
 

 
SECTIONAL WORKING MODEL OF TWO STROKE DIESEL ENGINE
 
(Model Made from Aluminiam material witch demonstrates all engine parts )
 

 
DIESEL ENGINE TWO STROKE IN CUT SECTION
 
DIESEL ENGINE TWO STROKE IN CUT SECTION
 
Actual original working engine is dissected wherever necessary so that all engine parts can be visualize
 

 
SECTIONAL WORKING MODEL OF FOUR STROKE DIESEL ENGINE
 
(Model Made from Aluminiam material witch demonstrates all engine parts )
 

 
DIESEL ENGINE FOUR STROKE SINGLE CYLINDER IN CUT SECTION
 
DIESEL ENGINE FOUR STROKE SINGLE CYLINDER IN CUT SECTION
 
Actual original working engine is dissected wherever necessary so that all engine parts can be visualize
 

 
DIESEL ENGINE FOUR STROKE DOUBLE CYLINDER IN CUT SECTION
 
Actual original working engine is dissected wherever necessary so that all engine parts can be visualize
 
DIESEL ENGINE FOUR STROKE THREE CYLINDER IN CUT SECTION
 
Actual original working engine is dissected wherever necessary so that all engine parts can be visualize
 
 
DIESEL ENGINE FOUR STROKE FOUR CYLINDER IN CUT SECTION
 
Actual original working engine is dissected wherever necessary so that all engine parts can be visualize
 
 
CRDI DIESEL ENGINE FOUR STROKE FOUR CYLINDER IN CUT SECTION
 
Actual original working engine is dissected wherever necessary so that all engine parts can be visualize
 
 
CRDI DIESEL ENGINE FOUR STROKE SIX CYLINDER IN CUT SECTION
 
Actual original working engine is dissected wherever necessary so that all engine parts can be visualize
 
 
TURBO CHARGE DIESEL ENGINE FOUR STROKE FOUR CYLINDER IN CUT SECTION
 
Actual original working engine is dissected wherever necessary so that all engine parts can be visualize
 
TURBO CHARGE DIESEL ENGINE FOUR STROKE SIX CYLINDER IN CUT SECTION
 
Actual original working engine is dissected wherever necessary so that all engine parts can be visualize
 
 
SELF STARTER
ALTERNATOR
SELF STARTER
ALTERNATOR
WORM & WHEELTYPE STEERING SYSTEM
HIGH PRESSURE FUEL PUMP MPFI
   
WORM & WHEELTYPE STEERING SYSTEM
HIGH PRESSURE FUEL PUMP MPFI
WORKING MODEL DISC BRAKE
ACTUAL MODEL OF CHASSIS OF JEEP
   
WORKING MODEL DISC BRAKE
ACTUAL MODEL OF CHASSIS OF JEEP
ACTUAL MODEL OF CHASSIS OF THREE WHEELER
LEAF SPRING SUSPENSION SYSTEM
   
ACTUAL MODEL OF CHASSIS OF THREE WHEELER
LEAF SPRING SUSPENSION SYSTEM
SHOCKER
FRONT AXLE WITH KING PIN
   
SHOCKER
FRONT AXLE WITH KING PIN
 
HYDRAULIC SHOCK ABSORBER
AIR SUSPENSION SYSTEM
   
HYDRAULIC SHOCK ABSORBER
AIR SUSPENSION SYSTEM
REAR AXLE ¾ FLOATING
DIFFERENTIAL
   
REAR AXLE ¾ FLOATING
DIFFERENTIAL
CARBURETORS SOLEX / AMAL / ZENITH
FUEL INJECTION PUMP AN AUTOMOBILE DIESEL ENGINE (INLINE)
 
CARBURETORS SOLEX / AMAL / ZENITH
FUEL INJECTION PUMP AN AUTOMOBILE DIESEL ENGINE (INLINE)
FUEL INJECTION PUMP AN AUTOMOBILE DIESEL ENGINE (ROTARY)
 
   
FUEL INJECTION PUMP AN AUTOMOBILE DIESEL ENGINE (ROTARY)
 
 

 
MODEL OF ELECTRICAL SYSTEM OF AN AUTOMOBILE FITTED ON BOARD WITH ACTUAL ELECTRICAL PARTS
 
This demonstration board which will give a complete idea of the electrical system of a maruthi car. In this demonstration board the actual wiring with parts and accessories of a car had been arranged, according to the electrical circuit of a car and terminals are provided to connect the battery. By giving connection the working of individual parts such as self starter, alternator, wiper motor, horn, head lights, tail lamps, parking lamps, side indicators, brake light, distributor, sparks of spark plugs, etc. , can be demonstrated. The parts sectioned to show the internal constructional details. This is a working demonstration model (battery not included in the rate).
 

 
IGITION SYSTEM OF PETROL ENGINE FITTED ON WOODEN BOARD
 

 
MPFI IGITION SYSTEM OF PETROL ENGINE FITTED ON BOARD
 

 
ELECTRICALLY OPERATED FUEL INJECTOR USED IN MPFI SYSTEM
 
 
The Model is made out of Original parts such as Single Brake disc, Single Caliper assembly single master cylinder etc, the model is mounted on a sturdy iron frame and can be demonstrated by operating the lever provided
 

 
WORKING MODEL DRUM BRAKE
 
WORKING MODEL DRUM BRAKE
 
This model is made out of original parts such as Single Brake drum assembly, single master cylinder wheel cylinders Brake Shoes, etc., the model can be demonstrated by operating the lever provided
 

 
WORKING MODEL DISC AND DRUM BRAKE COMBINED
 
This model contain two disc brakes in the front and two drum brakes at the rear and it is made out of original parts such as two master cylinder assembly (one sectioned and one working), wheel cylinder, brake drum, brake shoes, calipers etc. , suitably sectioned and mounted on a sturdy iron frame. By operating the lever provided, the working procedure of the model can be demonstrated.
 

 
WORKING MODEL POWER BRAKE
 

 
WORKING MODEL AIR BRAKE
 
This model is made of Original parts such as Air compressor, Un-loader valve, foot valve, Booster, Wheel assembly, air tank, control valve etc. The Brake system will be fitted with two front wheel assembly complete (without axle) and the drum will be suitably sectioned to show the working of the brake shoe. Other system will be mounted as it is and will be made to function (foot brake, hand brake etc will be functional.) The entire system will be mounted on a sturdy iron frame. A F.H.P Single phase 220/230 V AC motor will be coupled to the compressor for generation of the air, which is used for the operation of the model.
 

 
ACTUAL MODEL OF CHASSIS OF MARUTI CAR MOTORISED
 

 
ACTUAL MODEL OF CHASSIS OF TRUCK
 

 
INDEPENDENT SUSPENSION SYSTEM FRONT – MCPHERSON TYPE – ACTUAL DEMONSTRATION MODEL
 
This model is made out of original used parts, will be suitably sectioned and arranged to demonstrate the internal construction details showing the minute information with suspension strut with spring and shock absorber, disc brake, calliper, wishbone drive shaft etc., and working of the same can be shown, the model will be suitably painted and the entire model is mounted on a sturdy iron frame
 

 
INDEPENDENT SUSPENSION SYSTEM REAR - TORSION BAR TYPE - ACTUAL DEMONSTRATION MODEL
 

 
INDEPENDENT SUSPENSION SYSTEM FRONT - WISHBONE TYPE - ACTUAL DEMONSTRATION MODEL
 

 
GEAR & SECTOR TYPE STEERING SYSTEM
 

 
RACK & PINION TYPE STEERING SYSTEM COLLAPSIBLE
 

 
STEERING SYSTEM RECIRCULATING BALL TYPE
 

 
POWER STEERING GEAR & SECTOR TYPE
 
This model is made out of full size original parts, suitably sectioned and to demonstrate the working of Steering wheel worms, Steering arm, etc., is mounted on a sturdy iron frame.
 

 
POWER STEERING RACK & PINION TYPE
 
 
This model is made out of full size original parts, suitably sectioned and to demonstrate the working of Steering wheel worms, Steering arm, etc., is mounted on a sturdy iron frame.
 

 
REAR AXLE FULLYFLOATING
 

 
REAR AXLE SEMI FLOATING
 

 
TRANSAXLE
 

 
4X4/ TRANSFER CASE
 

 
GEAR BOX / TRANSMISSION CONSTANT MESH / SYNCHROMESH / SLIDING MESH
 

 
GEAR BOX / TRANSMISSION AUTOMATIC
 

 
LIMITED SLIP DIFFERENTIAL
 

 
GEAR BOX / TRANSMISSION WITH CLUTCH MANUAL / MOTORIZED
 

 
CLUTCH DIAPHRAGM TYPE
 
This model is made out of original parts such as Flywheel, Pressure Plate, Clutch plates, etc. to demonstrate the working of clutch assembly. By operating the pedal provided the model can be demonstrated. The entire model is mounted on a sturdy iron frame.
 

 
CLUTCH COIL SPRING TYPE
 
This model is made out of original used parts such as Flywheel, Clutch plates, etc. to demonstrate the working of clutch assembly. By operating the pedal provided the model can be demonstrated. The entire model is mounted on a sturdy iron frame.
 
DOUBLE DISC CLUTCH
 

 
CROSS AXLE DUAL
 

 
FLUID FLYWHEEL / TORQUE CONVERTOR
 

 
FLYWHEEL
 

 
PROPELLER SHAFT
 

 
UNIVERSAL JOINT OR UNIVERSAL COUPLING
 

 
CONSTANT VELOCITY JOINT (CV JOINT)
 

 

TRANSMISSION SYSTEM INCLUDING CLUTCH, GEAR BOX, PROPELLER SHAFT, DIFFERENTIAL FITTED ON M. S. FRAME. MOTORISED

 

 
4X4 WITH GEAR BOX CONNECTED WITH GEAR BOX FITTED ON A FRAME. MOTORISED
 

 
FOUR WHEEL DRIVE SYSTEM 4X4 WITH GEAR BOX CONNECTED WITH GEAR BOX & DIFFERENTIAL FITTED ON A FRAME MOTORISED
 

 
GEAR BOX ARRANGEMENT OF SCOOTER FITTED ON A WOODEN BASE. MANUAL DRIVEN
 

 
FRONT WHEEL DRIVE SYSTEM
 

 
REAR WHEEL DRIVE SYSTEM
 

 
MPFI SYSTEM WITH INJECTORS
 

 
AIR CONDITIONER COMPRESSOR PISTON TYPE / ROTARY TYPE
 

 
DISTRIBUTOR (CONTACT BREAKER POINT TYPE / ELECTRICAL TYPE)
 

 
WATER BODY
 

 
INTER COOLER
 

 
TURBO CHARGER
 

 
SILENCER
 

 
CATALYTIC CONVERTER
 

 
RESONATOR
 

 
OIL PUMP GEAR TYPE / ECCENTRIC TYPE / VANE TYPE /ROOTS TYPE
 

 
OIL FILTERS
 

 
AIR FILTERS, (ALL TYPES)
 

 
CYLINDER HEAD
 

 
WORKING MODEL OF LUBRICATING SYSTEM OF AN AUTOMOBILE ENGINE
 

 
WORKING MODEL OF COOLING SYSTEM OF AN AUTOMOBILE ENGINE
 

 
WORKING MODEL OF MPFI SYSTEM ON BOARD.
 

 
WORKING MODEL OF CRDI SYSTEM ON BOARD.
 

 
WORKING MODEL OF AIR CONDITIONER SYSTEM OFAN AUTOMOBILE
 

 
FUEL INJECTION PUMP AN AUTOMOBILE DIESEL ENGINE (CRDI)
 

FUEL PUMP AN AUTOMOBILE PETROL ENGINE DIAPHRAGM TYPE
 

FUEL PUMP AN AUTOMOBILE PETROL ENGINE ELECTRICAL TYPE.
 

GEAR BOXES
 
GEAR BOXES
 
a. Constant mesh gear box
b. Sliding mesh hear box
c. Synchromesh gear box
d. 4 speed gear box
e. Worm gear box
f. Planetary gear box
g. Differential Gear Box
h. Industrial Gear Box
 

BRAKE MODEL
a. Single Shoe Brake
b. Double Shoe Brake
c. Band Brake
d. Band & Block Brake
e. Internally Expanding Brake
f. Disc Brake Model
g. Disc Brake Actual Working
h. Hydraulic Brake Unit
i. Hydraulic Brake Unit (Two Brake Drums)
j. Hydraulic Brake Unit (Four Brake Drums)
i. Mechanical Brake System
k. Power Brake Actual Working
l. Air Brake Actual Working
 

 
FUEL INJECTION PUMP (DIESEL) ROTARY
 
4 barrel type, pressure : 35 kg/cm2
 

 
FUEL INJECTION PUMP CALIBRATION EQUIPMENT AND ITS ACCESSORIES AND SPECIAL TOOLS WITH ATTACHMENT FOR DISTRIBUTOR PUMP AND IN LINE PUMP
 
Drive Motor :
5 HP (3.7 kw) 3 phase
Number of Cylinders :
8
Speed Control :
0 to 3000 rpm
Speed converter :
Hydraulic stepless speed converter
Tachometer :
Electronic 0 to 3000 rpm 1 grade for 20 rpm.
Stroke-setting device :
between 100-1200 Strokes.
Length Width Height :
52�² X 30�² X 70�²
Weight :
450 kg.
Oil tank :
60 liter
 

 
FUEL PUMP
 
Pressure – 3 bar flow – 90 L/H
 

 
FUEL FEED PUMP
 

 
FUEL INJECTION PUMP (DIESEL) INLINE
 
Single Barrel
 

 
PETROL FUEL PUMP OF MPFI SYSTEM
 

 
HYDRAULIC JACK- HIGH (TROLLEY TYPE) 2000 KG CAPACITY
 
Application -
Passenger Cars, Light Commercial Vehicles, Heavy Vehicles, Heavy Side frames for greater stability, Hand Chrome Plated Piston, Burnished Cylinder, Powder Coated finish
 

 
HYDRAULIC JACK HI - LIFT (TROLLEY TYPE )
 
Capacity
Tons
8
No. of posts
1
Plunger diameter
mm
320
Operating pressure
kg/cm2
9 to 12
Lifting height
mm
1525
Ramp length
- Front
mm
5800
- Rear
mm
-
Ramp Width
mm
820
Oil fill capacity
ltrs
175
 
CUT-SECTION MODEL OF DEMONSTRATION CHASIS WORKING WITH ELECTIRCALS OF A CAR/VAN (MARUTI)
 
The model will be made of full size original used car chassis consisting of the four-stroke three-cylinder petrol engine. The cut section model will be constructed such that the following systems can be demonstrated in working conditions.

ENGINE: Maximum parts and accessories of an engine like three of the cylinder, cylinder head, Inlet and Exhaust manifolds, Carburetor, Distributor, self-starter, Dynamo, Water pump, Radiator, etc, are sectioned to show the internal constructional details.

TRANSMISSION SYSTEM: It will consist of Clutch and gearbox assembly, the casing of which is suitably cut to demonstrate its operation. The Hydraulic circuit from the pedal to the Clutch is active and will help to demonstrate the response of hydraulic systems. The gearbox will be coupled to Differential gear box with an axle and the different coupling used for this transmission can be demonstrated.

The Differential gear box is also cut so as to clearly to demonstrate its complete operating principle.

FUEL SYSTEM: The Fuel tank will be cut to expose the mounting of the level sensor and the position of Fuel section. The system will have a mechanical Fuel pump.

EXHAUST SYSTEM: Will have Exhaust Manifold and silencer in cut section to explain internal construction.

LUBRICATION SYSTEM: Will show engine Lubrication system along with the Lubrication oil pump.

SUSPENSION SYSTEM : This will explain both the Hydraulic Suspension systems at the front and the leaf spring Suspension at the Rear. One of the hydraulic arrangements of Suspension mechanism has to be highlighted (with Shock absorbers) and explained cut
section ally.

BRAKING SYSTEM : This Hydraulic circuit of the Hydraulic Braking mechanism will be operational.

STEARING MECHANISM : This will include Steering wheel, Steering gear and coupling at the wheels.
 

 
CUT SECTION MODEL OF STEERING GEAR BOX (WORKING):
 
This model is made out of full size original parts, suitably sectioned and to demonstrate the working of Steering wheel worms, Steering arm, etc., is mounted on a sturdy iron frame.
 

 
WORKING MODEL OF POWER STEERING WITH WHEEL AND AXLE:
 
This model will be made of full size original parts, suitably mounted to demonstrate the working of power Steering mechanism etc using motor.The Arrangement Of Wheels And Axle Connecting To steering system has to be done such that the movement of the wheels when rotating the steering wheels can be displayed .The model will be mounted on to a tubular frame.
 

 
CUT SECTION MODEL OF SLIDING MESH GEAR BOX OF TATA VEHICLE (WORKING):
 
This model will be made of original full size used gearbox, suitably sectioned to show the gear mechanism of forward and reverse speeds. A Crank lever will be provided to demonstrate the mechanism. Complete unit is mounted on a sturdy iron frame.
 

 
CUT SECTION MODEL OF FULLY FLOATING DIFFERENTIAL AND REAR WHEEL MECHANISM (WORKING):
 
This model will be made of original used heavy vehicle parts, suitably sectioned to show clearly the action of Differential gear box, such as pinion crown wheel in Differential and Brake drums in Rear axle, A Crank handle will be provided to demonstrate the model. The model is mounted on a sturdy iron frame
 

 
CUT SECTRION MODEL OF HYDRAULIC BRAKE UNIT-FOUR WHEEL TYPE (CUT SECTIONED AND WORKING) WITH TWO DISC AND DRUM BRAKES.
 
This model will have two disc brakes in the front and two drum brakes at the rear and made of original parts such as two master cylinder Assembly (one sectioned and one working), wheel cylinder, Brake drum, Brake Shoes, calipers etc. suitably sectioned & mounted on a sturdy iron frame. By operating the lever provided, the working procedure of the model can be demonstrated.
 

 
DEMONSTRATION BOARD OF IGNITION SYSTEM OF AN AUTOMOBILE 4 WHEELER (WORKING):
 
This open demonstration-working unit will be made of original used parts such as switches, ignition coil, Distributor, four spark plugs and a battery for power source, with necessary wiring connections. By switching on the switch and by giving rotation to the Distributor, Sequential Sparks in the spark plugs can be demonstrated.
 

 
CUT SECTION MODEL OF MECHANICAL BRAKESYSTEM (WORKING)
 
This model will be made of original used parts such as Brake drum, Brake Shoes, Brake peddle, etc., suitably sectioned and mounted on a wooden base. By operating the Brake drum and applying the Brake pedal this model can be demonstrated.
 

 
CUT SECTION MODEL OF DIAPHRAM CLUTCH SYSTEM (WORKING)
 
This model will be made of original parts such as Flywheel, Pressure Plate .Clutch plates, etc. to demonstrate the working of clutch assembly. By operating the pedal provided the model can be demonstrated. The entire model is mounted on a sturdy iron frame.
 

 
CUT SECTION MODEL OF COMPELETE COIL SPRING TYPE FRONT SUSPENSION SYSTEM
 
This model will be made of original used parts, suitably sectioned and Arranged to demonstrate the internal construction details showing the minute information With Suspension with Coil spring and wheels mounted on bearing on tapered spindles of the steering knuckles, drive shaft etc., and working of the same can be shown.
 

 
CUT SECTION MODEL OF COMPELETE BOTH SIDE WITH DOUBLE WISHBONE SUSPENSION WITH DRIVE SHAFT
 
This model will be made of original used parts, suitably sectioned and Arranged to demonstrate the internal construction details showing the minute information With Suspension Strut with spring and shock absorber, disc brake, callipers drive shaft etc., and working of the same can be shown.
 

 
CUT SECTION MODEL OF COMPELETE LEAF SPRING SUSPENSION SYSTEM WITH REAR AXLE
 
This model will be made original used parts, will be suitably sectioned And Arranged to demonstrate the internal construction details showing the minute information With leaf spring is arranged along with shock absorber etc., and working of the same can be shown, the model will be suitably painted and The entire model is mounted on a sturdy iron frame.
 

 
DEMONSTRATION BOARD OF MPFI SYSTEM
 
This open demonstration Board will be made of original used parts such as such as petrol injector, inlet manifolds, throttle body, distributor, ECU, canister purge valve, carbon canister, fuel tank module, supporting sensors such as lambda sensor, engine speed sensor, cam position sensor etc,., with necessary wiring connections to show the circuit connections. The entire system will be suitably sectioned and mounted on board.
 

 
CUT SECTION WORKING MODEL OF LUBRICATION SYSTEM OF 4 CYLINDER PETROL ENGINE
 
It will consist of engine lubrication system along with the lubricating oil pump section to show the parts as table model. Further a 4 cylinder petrol engine with crank case chamjer with cylinder head sectioned, crank shaft, cam shaft, oil pump, oil filter, chain with rack has to be used to run the oil pump by hand wheel to show working of lubricating system and oil line with rocker arm line, rocker arm shaft and lift and other lubrication parts with motor driven system
 

 
POWER STEERING
 
Front 2 No. wheels mounted on rigid front axle & inter linked with tie rod. Transverse link, rack, pinion, steering servo assembly. A separate hydraulic power pack maintains pressure inside the servo assembly. By turning the steering wheel servo motor supplies the pressurized oil to two front wheel by that wheel gets turned in either direction. All components & assembly mounted on sturdy M. S. frame duly painted.
 
1. Front wheels : 2 Nos.
2. Front axle : 1 No.
3. Tie rod : 1 No.
4. Transverse link : 1 No.
5. Servomotor : 1 No.
6. Hydraulic power pack : 1 No.
7. Pressure relief valve : 1 No.
8. Oil pipes : 1 Set
 
MODEL OF RADIATOR
 

 
MODEL OF SURFACE CONDENSER
 
It Consists of
a. Pneumatic Brake Assembly
b. Booster assembly
c. Wheel & Brake Drum with wheel cylinder
d. Mini compressor with air cylinder
e. M. S. mounting base
 

 
MODEL OF PETROL INJECTION SYSTEM
 
This open demonstration Board will be made of original used parts such as such as inlet manifolds, throttle body, Cylindrical head, petrol injectors, All injectors mounted in cylinder head. The entire system will be suitably sectioned and mounted on board.
 

 
FUEL SUPPLY SYSTEM OF PETROL ENGINE
 
This unit consists of fuel tank float, fuel indicator, carburetor, fuel filter etc. all connected with rubber hose & mounted on wooden base.
 

 
FUEL SUPPLY SYSTEM OF DIESEL ENGINE.
 
This unit consists of diesel tank with float indicator, diesel filter unit ( Primary & Secondary ) fuel indicator fuel pump etc. mounted on wooden base.
 

 
WORKING MODEL OF EDUCATION CAR MODEL
 

 
ELECTRONIC IGNITION SYSTEMS OF AN AUTOMOBILE
 

 
FUEL PUMP AN AUTOMOBILE DIESEL ENGINE DIAPHRAGM TYPE
 

 
FUEL PUMP AN AUTOMOBILE DIESEL ENGINE ELECTRICAL TYPE.
 

 
CUT-SECTION MODEL OF DEMONSTRATION CHASIS JEEP
 
CUT-SECTION MODEL OF DEMONSTRATION CHASIS JEEP
 
The model will be made of full size original used jeep chassis consisting of the four-stroke four-cylinder diesel engine. The cut section model will be
constructed such that the following systems can be demonstrated in working conditions.

ENGINE: Maximum parts and accessories of an engine like four of the cylinder, cylinder head, Inlet and Exhaust manifolds, fuel Pump, self-starter,
Dynamo, Water pump, Radiator, etc, are sectioned to show the internal constructional details.

TRANSMISSION SYSTEM: It will consist of Clutch and gearbox assembly, the casing of which is suitably cut to demonstrate its operation. The Hydraulic circuit from the pedal to the Clutch is active and will help to demonstrate the response of hydraulic systems. The gearbox will be coupled to Differential gear box with an axle and the different coupling used for this transmission can be demonstrated. The Differential gear box is also cut so as to clearly to demonstrate its complete operating principle.

FUEL SYSTEM: The Fuel tank will be cut to expose the mounting of the level sensor and the position of Fuel section. The system will have a mechanical
Fuel pump.

EXHAUST SYSTEM: Will have Exhaust Manifold and silencer in cut section to explain internal construction.

LUBRICATION SYSTEM: Will show engine Lubrication system along with the Lubrication oil pump.

SUSPENSION SYSTEM : This will explain both the Hydraulic Suspension systems at the front and the leaf spring Suspension at the Rear. One of the hydraulic arrangements of Suspension mechanism has to be highlighted (with Shock absorbers) and explained cut section ally.

BRAKING SYSTEM : This Hydraulic circuit of the Hydraulic Braking mechanism will be operational.

STEARING MECHANISM : This will include Steering wheel, Steering gear and coupling at the wheels.
 

 
BATTERY IGNITION SYSTEM IN WORKING CONDITION
 
The unit is so constructed to demonstrate the switch, distributor 4 spark plug, ignition coil etc. mounted on wooden board.
 

 
CARBURETORS IN CUT SECTION (1) S.U. (2) SOLEX
 
Original second hand carburetors in cut section on stand.
 

 
BOSCH FUEL INJECTION PUMP IN CUT SECTION
 
a. Four Barrel Type.

Showing the movement of plunger of elements inside the barrel, delivery valve camshaft feed pump is also in cut section, pneumatic governing system etc. One handle is attached for the movement of camshaft.

b. Distributor Type ( Rotary ) fuel Pump in cut Section
 

 
FUEL PUMP OF PETROL ENGINE IN CUT SECTION
 
a. Mechanical Type.
b. Electrical Type.
 

 
DISTRIBUTOR IN CUT SECTION
 
DISTRIBUTOR IN CUT SECTION
 
Original second hand distributor so that we can see the advance mechanism by centrifugal type & pneumatic type, also contact breaker, rotor & condenser.
 

 
CAR GEAR BOX ( 5 SPEED ) IN CUT SECTION
 
Original second hand gear box rear assembly of car or jeep is sectioned to demonstrate the working of bevel & pinion crown wheel, too plant gears & two sun gears, final drive gear shafts & brake drums complete unit is fixed on sturdy wooden base.
 

 
STEERING GEAR MECHANISM
 
Original second hand steering mechanism of jeep mounted on sturdy wooden base & steering gear box is dissected to demonstrate worm & worm wheel or sector gears drag link, drop arm, tie rod & wheel arm.
 

 
 
Address: DATACONE ENGINEERS PVT. LTD.
271, `Samrajya’, Near Sangliwadi High School, Sangliwadi,
SANGLI - 416416. Maharashtra, INDIA.
Tel. No.: +91 - 233 - 2535197, 2535759, 2535841, 2850851
Fax: +91 - 233 - 2535769
Cell: +91 - 94220 40681, 97646 79181
Visit Also : www.dataconeequip.com, www.refrigerationandairconditioninglaboratory.com, www.thermodynamicslaboratory.com , www.fluidmechanicslaboratory.com, www.heattransferlaboratory.com
Last updated: 11.10.2014